進口化工離心泵｜美國進口化工離心泵
進口化工離心泵參數:
流量：6.3～400m3/h；
揚程：5～132m；
轉速：2900、1450r/min；
功率：0.55～110KW；
進口直徑：50～200mm；
zui高工作壓力：1.6Mpa。
進口化工離心泵工作原理:
化工離心泵除了葉輪的作用之外，螺旋形泵殼起的作用也是很重要的。從葉輪里獲得了能量的液體流出葉輪時具有較大的功能，這些液體在螺旋形泵殼內被收集起來，并在后面的擴散管里把動能變成壓力能。
化工離心泵與其他種類的泵相比，它具有構造簡單、不易磨損、運行平穩、噪音小、出水均勻、調節方便、效率高等優點，因此化工離心泵得到了廣泛的應用。
進口化工離心泵安裝說明:
裝時管路重量不應加在水泵上，應有各自的支承體，以免使變形影響運行性能和壽命。
2. 泵與電機是整體結構，安裝時無需找正，所以安裝時十分方便。
3. 安裝時必須擰緊地腳螺栓，以免起動時振動對泵性能的影響。
4. 安裝水泵前應仔細檢查泵流道內有無影響水泵運行的硬質物（如石塊、鐵粒等），以免水泵運行時損壞葉輪和泵體。
5. 為了維修方便和使用安全，在泵的進出口管路上各安裝一只調節閥及在泵出口附近安裝一只壓力表，以保證在額定揚程和流量范圍內運行，確保泵正常運行，增長水泵的使用壽命。
6. 泵用于吸程場合，應裝有底閥，并且進口管路不應有過多彎道，同時不得有漏水，漏氣現象。
7. 排出管路如逆止閥應裝在閘閥的外面。
8. 安裝后撥動泵軸，葉輪應有摩擦聲或卡死現象，否則應將泵拆開檢查原因。
9. 泵的安裝方式分為硬性聯接和柔性聯接安裝。
進口化工離心泵維護以及保養:
1. 水管路必須高度密封。
2. 禁止泵在汽蝕狀態下*運行。
3. 禁止泵在流量運行時，電機超電流*運行。
4. 定時檢查泵運行時，電機超電流*運行。
5. 泵在運行過程中應有專人看管，以免發生意外。
6. 泵每運行500小時應對軸承進行加油。電機功率大于11KW配有加油裝置，可用高壓油槍直接注入，以保證軸承潤滑優良。
7. 泵進行*運行后，由于機械磨損，使機組噪聲及振動增大時，應停車檢查，必要時可更換易損零件及軸承，機組大修期一般為一年。
進口化工離心泵美國泰樂TYLER售后服務：
用戶*，信譽*，優質、完善的售后服務是我們產品價值的延伸和對客戶利益的重要保證，我公司服務質量管理體系的宗旨是：建立并不斷完善科學、合理、高效的服務質量管理體系，公正、準確、及時地完成客戶的售后服務質量保障工作，為我公司的客戶服務建立良好、全面、充分的服務體系。
Chemical centrifugal pump
Imported chemical centrifugal pump parameters:
Flow: 6.3 ~ 400m3/h;
Head: 5 ~ 132m;
Speed: 2900, 1450r/min;
Power: 0.55 ~ 110KW;
Inlet diameter: 50 ~ 200mm;
Maximum working pressure: 1.6Mpa.
Working principle of centrifugal pump:
Chemical centrifugal pump in addition to the role of the impeller, the role of spiral pump shell is also very important. From the impeller to obtain the energy of the liquid flow out of the impeller has a larger function, these liquids are collected in the spiral pump shell, and in the back of the diffusion tube into kinetic energy into pressure.
Compared with other kinds of chemical centrifugal pump pump, it has the advantages of simple structure, easy to wear, smooth operation, low noise, uniform, convenient adjustment and high efficiency, so the chemical centrifugal pump has been widely used.
Chemical centrifugal pump installation instructions:
The weight of the pipeline should not be added to the pump, should have their own support body, so as not to affect the deformation performance and life.
2 pump and motor is the overall structure, no need to find the correct installation, so very convenient installation.
3 installation of anchor bolts must be tightened to avoid starting when the vibration on the pump performance.
4 before installing the pump should carefully check whether there is any influence on the pump pump running hard objects (such as stones, iron particles, etc.), in order to avoid damage to the impeller pump and pump body.
5 for easy maintenance and safe use, the installation of a control valve and a pressure gauge installed in the pump outlet near the pump inlet and outlet pipe, to ensure operation at rated lift and flow range, to ensure the normal operation of pumps, increase the service life of the pump.
6 pump for suction occasions, should be equipped with bottom valve and inlet pipe should not be too many corners, and shall not have Water Leakage leakage phenomenon.
7 discharge pipe such as check valve should be installed outside the gate.
After the installation of 8 toggle pump shaft, impeller due to friction sound or death card, otherwise the pump should be opened to check the reason.
9 pump installation method is divided into rigid connection and flexible connection installation.
Chemical centrifugal pump maintenance and maintenance:
1 water pipes must be highly sealed.
2 prohibit the long-term operation of the pump cavitation.
3 prohibit the pump running in the flow, motor over current operation for a long time.
4 check the operation of the pump, the motor current over a long period of time.
5 pumps in the course of operation should be someone to guard against accidents.
6 pump run every 500 hours to deal with bearing oil. The motor power is greater than 11KW with a refueling device, use the high pressure oil is injected directly into the gun, in order to ensure good bearing lubrication.
7 long term operation of the pump, due to mechanical wear, so that the noise and vibration of the unit increases, should stop the inspection, if necessary, can replace the vulnerable parts and bearings, the unit overhaul period is generally one year.
The United States imports of chemical centrifugal pump Taylor TYLER customer service service:
Customer first, reputation first, customer service quality, perfect service is the important guarantee of our products and to extend the value of the interests of customers, our service tenet is: quality management system, establish and improve the service quality management system is scientific, reasonable and efficient, fair, accurate and timely completion of customer service and customer service quality assurance the establishment of good, comprehensive, full service system for my company's customer service.
